Repair Guides

How to Install Storm Panels Without TracksDirect mount on permanent rated anchors

Storm panels do not need a header track and sill track: they can mount straight to the wall on permanent, rated anchors at the header, the sill or both. We use PanelMate anchors, which stay in the wall year-round with either a threaded stud or a flush threaded socket, and they only hold their rating at the spacing the engineering calls for.

PanelMate
Rated Anchors
Male or Female
Stud or Flush Socket
Header, Sill or Both
Where They Go
$22 / $26
Aluminum / Clear per sq ft
Engineered
Spacing and Embedment

How it works

Direct-mount storm panels

Most storm panels hang from a header track above the window and sit in a sill track below it. A direct-mount install skips one or both tracks. Instead, permanent anchors go into the wall around the opening, and the panels bolt straight to them before a storm. The anchors stay in place all year, so putting the panels up is the same job every time: line up the holes and tighten the fasteners.

Male and female PanelMate anchors for storm panels without tracks, section viewMale PanelMateFemale PanelMateSection through the wall at one fastener. Spacing and embedment come from the engineering for your wall.Anchor in the wallpermanent, engineered spacingThreaded studcapped between stormsStorm paneledge viewFlush threaded socketnothing sticks outSidewalk boltthreads into the socketWing nuttightens over the panel on a male anchor
Male PanelMate

Leaves a threaded stud sticking out of the wall. The panel slides over the studs and a wing nut holds it. Fastest to hang, especially at the top of the opening, where the panel can rest on the studs while you work. Studs are capped between storms.

Female PanelMate

Sits flush with the wall with a threaded socket inside. The panel is held with a sidewalk bolt that threads into it. Nothing sticks out of the wall the rest of the year, which suits entries, walkways and anything people brush past.

Header, sill or both

Anchors can replace the header track, the sill track or both. A common setup keeps a header track and uses anchors at the sill, or uses male anchors at the top and female at the bottom so panels hang easily and the sill stays clean.

Doing it right

What makes a track-free install rated

PanelMate anchors are tested to the Miami-Dade hurricane standards, but the test only covers anchors installed the way the approval says. Three things decide whether your install holds:

  • The wall material. Poured concrete, filled block, hollow block, brick and wood framing each take a different anchor and a different spacing.
  • Spacing and edge distance. The engineering sets how far apart the anchors go and how far they stay from the edge of the opening and the edge of the block.
  • Embedment. The anchor has to reach the depth the approval calls for, through stucco or brick veneer into the structure behind it.

Get any of the three wrong and the panel may look fine and still pull off the wall in a storm. That is the main reason we install these ourselves rather than selling anchors over the counter.

Aluminum storm panels$22 per sq ft installed
Clear storm panels$26 per sq ft installed
AnchorsPanelMate, male or female
WhereHeader, sill or both
Full price list2027 price guide
Already have anchors?
If your panels are on PanelMates and a stud is bent or a socket is stripped, a single anchor can usually be replaced on a service call. See the parts diagrams for the rest of a panel system.

When panels without tracks are the wrong choice

Direct mount is clean and fast on the right wall. Here is when it is not.

The wall cannot hold an anchor where it needs one
Stucco over foam, soft or crumbling block, or an opening right at the edge of the wall may not give the embedment or edge distance the approval needs. A track that spreads the load may be the answer.
The panels have to clear trim or a projecting window
Direct-mount panels sit tight to the wall. If the window or its trim sticks out, the panels need build-out, and a track or angle usually does that better.
You plan to drill it yourself
Spacing, edge distance and embedment are set by engineering. An anchor in the wrong place is a hole in the wall, not protection.

Storm panels without tracks: questions

Can storm panels be installed without tracks?
Yes. Panels can mount straight to the wall on permanent, rated anchors at the header, the sill or both, instead of a header track and sill track. We use PanelMate anchors for this.
What is a PanelMate?
A permanent storm panel anchor that stays in the wall year-round. The male version leaves a threaded stud for a wing nut. The female version sits flush and takes a sidewalk bolt.
Should I use male or female anchors?
Male anchors make panels faster to hang, because the panel hooks over the studs. Female anchors leave nothing sticking out of the wall. Many installs use male at the top and female at the bottom, or the same type at both.
Are storm panels without tracks hurricane rated?
Yes, when the anchors are rated and installed at the spacing and embedment the engineering calls for on your wall. Wrong anchors or wrong spacing void the rating.
Can I install PanelMates myself?
We do not recommend it. The spacing, edge distance and embedment depend on the wall material and your wind zone, and a wrong guess is invisible until a storm.
How much do storm panels cost?
Aluminum storm panels are $22 per square foot installed and clear panels are $26. See the price guide for full-house examples.

Why homeowners call AHS

Family-owned since 2006, with our own crews on every job.

Licensed in NC and SC
NC General Contractor L.66775 · SC General Contractor CLG.118108.GC
4.7 stars on Google
From 65 Google reviews.
7-Year Workmanship Warranty
On every installation we do.

Panels Without the Tracks

Book a free estimate. We check your wall, pick the anchors and tell you whether tracks or direct mount fit your house.

(910) 256-1288
Available 24/7 · Free estimates
Request Free Estimate
Matthew Burns
Scroll to Top