Hurricane Shutter PartsLabeled diagrams for every shutter type
Every hurricane shutter is a handful of parts doing one job: holding a panel, slat or fabric in front of the glass and keeping it there in high wind. These labeled diagrams show the parts of accordion, roll down, Bahama, colonial, storm panel and hurricane screen systems, what wears out, and when to stop and call us.
Before you start
Know the part before you call
Most shutter problems come down to one worn or damaged part. Knowing its name saves time on the phone and helps you tell a five-minute fix from a job that needs a technician. The diagrams below are drawn from tested product approval drawings for each system type. Names and details vary a little from brand to brand, but the parts do the same jobs.
Two rules apply to every system. First, do not take apart anything that carries a load in a storm, like anchors, tracks or the fasteners that hold them to the wall. Those were sized by an engineer for your house. Second, if a part is bent, cracked or missing, replace it rather than straightening or patching it. A rated shutter is only rated when every part is in place.
| Service call | $295, includes the first hour on site |
| Each additional hour | $150 |
| Parts | Extra, quoted before we install them |
| Brands | Every brand, whoever installed it |
Accordion shutters
Parts of an accordion shutter
Wheels and nylon bushings wear first, then locks. Sand packs into the bottom track, and salt corrodes pins and fasteners on the ocean side of the house.
Vacuum or rinse the bottom track, then lubricate the wheels, pins and lock with a dry silicone spray. Our accordion lubrication guide walks through it.
A blade is bent, the lock will not turn, the centermate will not latch, or the stack drags even with a clean track. Bent blades and broken wheel carriages need replacing.
Roll down shutters, outside
Parts of a roll down shutter
Base slats and end retention clips take the most wear. Slats dent from debris, and side rails collect sand and leaves that make the curtain bind.
Keep the side rails clean and rinse salt off the curtain a few times a year. Never force a curtain that has stopped. Forcing it bends slats and can strip the motor.
The curtain stops partway, comes out of a rail, makes grinding noises, or a slat is cracked or missing. See roll down troubleshooting for electric shutters.
Roll down shutters, inside the hood
The roll down hood assembly
Motors, slat hanger straps, and the crank parts on override and manual systems. Straps can tear, and motors lose their limit settings or fail with age.
If an electric shutter will not move, check the breaker and the remote battery, then try the wall switch. On an override motor, the crank should still work.
The motor hums but the tube does not turn, the shutter stops short of the top or bottom, the crank spins freely, or you hear the curtain slipping inside the hood.
Bahama shutters
Parts of a Bahama shutter
Header hinges and the side arms. Arms seize when salt gets into the telescoping pipes, and thumbscrews and tension rings corrode or go missing.
Rinse and lubricate the arms and hinges, and keep the pins and thumbscrews together in one place so they are there when you need them.
A hinge is cracked, an arm will not slide or lock, louvers are broken, or the shutter will not sit flat in the closed position.
Colonial shutters
Parts of a colonial shutter
Hinges, hinge bolts and the storm bar hardware. Panels can sag on worn hinges, and the sill bolts and rivet nuts corrode.
Open and close the panels a few times a year so the hinges do not freeze, and check that the storm bar and its pins are where you can find them.
Panels sag or will not close square, a hinge or bolt is broken, or the storm bar no longer lines up with its brackets.
Storm panels
Parts of a storm panel system
Studs, wing nuts and sidewalk bolts, plus the anchors in the header and sill. Panels themselves last for decades if they are stored flat and dry.
Count the panels and fasteners before the season and store them by opening. Replace stripped wing nuts with stainless ones rated for the job.
A header or sill track has pulled loose, studs are bent or missing, panels are cracked, or you have panels but no track. Read how to install storm panels properly before you improvise.
Hurricane screens
Parts of a hurricane screen
The keder edge, the tension spring and the bottom hembar. Fabric can tear at the edge if it is run out of its track, and motors wear like any roll down motor.
Keep the side rails clear and never run the screen with something in its path. Rinse the fabric with fresh water after a storm.
The fabric comes out of a rail, will not track straight, is torn, or the motor stops. Our hurricane screens page covers the systems we install.
When a DIY parts fix is the wrong choice
Cleaning and lubricating are yours. These are not.
Hurricane shutter parts questions
Why homeowners call AHS for service
Family-owned since 2006. We answer emergency calls 24/7.
Related Resources
Need a Part Replaced?
Call to book a service call. Most parts are on the truck, so most repairs take one visit.
- How to Lubricate Accordion Shutters | Pro Tips | AHS - April 17, 2026
- Design Guide: Best Hurricane Shutters & Colors for Brick Homes | AHS - April 16, 2026
- Get the Miami Look: Bahama Shutter Styles for Your Carolina Home - April 15, 2026
