Repair Guides

Hurricane Shutter PartsLabeled diagrams for every shutter type

Every hurricane shutter is a handful of parts doing one job: holding a panel, slat or fabric in front of the glass and keeping it there in high wind. These labeled diagrams show the parts of accordion, roll down, Bahama, colonial, storm panel and hurricane screen systems, what wears out, and when to stop and call us.

6 Systems
Labeled Diagrams
Every Brand
We Service
On the Truck
Most Common Parts
$295
Service Call, First Hour
24/7
Emergency Calls

Before you start

Know the part before you call

Most shutter problems come down to one worn or damaged part. Knowing its name saves time on the phone and helps you tell a five-minute fix from a job that needs a technician. The diagrams below are drawn from tested product approval drawings for each system type. Names and details vary a little from brand to brand, but the parts do the same jobs.

Two rules apply to every system. First, do not take apart anything that carries a load in a storm, like anchors, tracks or the fasteners that hold them to the wall. Those were sized by an engineer for your house. Second, if a part is bent, cracked or missing, replace it rather than straightening or patching it. A rated shutter is only rated when every part is in place.

Service call$295, includes the first hour on site
Each additional hour$150
PartsExtra, quoted before we install them
BrandsEvery brand, whoever installed it
Not sure what you have?
Look for the permanent label on the housing, track or panel and send us a photo. It names the manufacturer and the product approval.

Accordion shutters

Parts of an accordion shutter

Accordion hurricane shutter parts diagramAccordion shutter, closed, seen from outside. Based on typical tested accordion assemblies; parts vary by brand.Header tracktop track the shutter hangs fromWheel carriagenylon wheels that roll in the headerWindow bladeclear polycarbonate openingsHinge knucklenylon bushings and accordion pinsEnd starterfixes the stack to the wallBottom (sill) trackblades ride in it, sand collects hereBladeinterlocking aluminum bladeCentermatewhere the two stacks meetLockkey or thumbturnLocking roddrops into the bottom trackSide angle or end starteron the far jamb
What wears out

Wheels and nylon bushings wear first, then locks. Sand packs into the bottom track, and salt corrodes pins and fasteners on the ocean side of the house.

What you can do

Vacuum or rinse the bottom track, then lubricate the wheels, pins and lock with a dry silicone spray. Our accordion lubrication guide walks through it.

Call us if

A blade is bent, the lock will not turn, the centermate will not latch, or the stack drags even with a clean track. Bent blades and broken wheel carriages need replacing.

Roll down shutters, outside

Parts of a roll down shutter

Roll down hurricane shutter parts diagramRoll down shutter, partly lowered, seen from outside. The motor or crank mechanism is inside the housing; see the hood diagram.Housing (hood)box that holds the rolled-up curtainEnd capcloses each end of the housingSide rail (guide track)the curtain runs in itEnd retention clipkeeps slats in the rail in high windSlats (curtain)interlocking aluminum slatsBase slat (bottom bar)heavier bottom slat, seals at the sillLockon manual shuttersCrank gear boxmanual shuttersWall switch or remoteelectric shutters
What wears out

Base slats and end retention clips take the most wear. Slats dent from debris, and side rails collect sand and leaves that make the curtain bind.

What you can do

Keep the side rails clean and rinse salt off the curtain a few times a year. Never force a curtain that has stopped. Forcing it bends slats and can strip the motor.

Call us if

The curtain stops partway, comes out of a rail, makes grinding noises, or a slat is cracked or missing. See roll down troubleshooting for electric shutters.

Roll down shutters, inside the hood

The roll down hood assembly

Roll down shutter hood assembly diagram, override and non-override motorOverride motorNon-override motorReel tube (axle)the curtain rolls up on itEnd capMotor drive and wheel stopSlat hangers (straps)connect the top slat to the tubeOverride motormotor plus manual backupMotor bracketExtension shaftUniversal jointCrank handleraises it when the power is outTubular motorinside the tube, no crankCrownturns the tube with the motorMotor bracket and clipsBearing end capfree end of the tubeSlat hangers (straps)
What wears out

Motors, slat hanger straps, and the crank parts on override and manual systems. Straps can tear, and motors lose their limit settings or fail with age.

What you can do

If an electric shutter will not move, check the breaker and the remote battery, then try the wall switch. On an override motor, the crank should still work.

Call us if

The motor hums but the tube does not turn, the shutter stops short of the top or bottom, the crank spins freely, or you hear the curtain slipping inside the hood.

Bahama shutters

Parts of a Bahama shutter

Bahama hurricane shutter parts diagramBahama shutter propped open for shade. For a storm the arms come off and the panel is lowered and pinned closed.Headermounted above the windowHeader hingethe panel swings from hereLouver bladesfixed blades, set at an angleTension ring and thumbscrewlocks the arm lengthTelescoping side arminner and outer aluminum pipeArm bracketon the jamb or wallStile (side frame)Sill or bottom angleclosed positionL-pin or slide pinpins the panel shut for a storm
What wears out

Header hinges and the side arms. Arms seize when salt gets into the telescoping pipes, and thumbscrews and tension rings corrode or go missing.

What you can do

Rinse and lubricate the arms and hinges, and keep the pins and thumbscrews together in one place so they are there when you need them.

Call us if

A hinge is cracked, an arm will not slide or lock, louvers are broken, or the shutter will not sit flat in the closed position.

Colonial shutters

Parts of a colonial shutter

Colonial hurricane shutter parts diagramPair of colonial shutters closed for a storm. Day to day they stand open beside the window.Top railLouver bladesin a fixed frameHingeflat or double hinge on the jambJambmounted beside the windowBottom railHinge bolt and lock nutStorm barbolted across both panelsSafety pin or boltholds the storm barSidewalk bolt and rivet nutlocks panels at the sill
What wears out

Hinges, hinge bolts and the storm bar hardware. Panels can sag on worn hinges, and the sill bolts and rivet nuts corrode.

What you can do

Open and close the panels a few times a year so the hinges do not freeze, and check that the storm bar and its pins are where you can find them.

Call us if

Panels sag or will not close square, a hinge or bolt is broken, or the storm bar no longer lines up with its brackets.

Storm panels

Parts of a storm panel system

Storm panel hurricane shutter parts diagramStorm panels installed over a window. Panels go up before a storm and are stored the rest of the year.Header trackH or F header above the windowPanel fastenerbolt or wing nut at the topAluminum storm panelcorrugated for stiffnessPanel overlapeach panel overlaps the nextSill track or anchorsbottom of the openingClear panelpolycarbonate, lets light inWing nut on studholds each panel at the sillSidewalk boltif no sill track
What wears out

Studs, wing nuts and sidewalk bolts, plus the anchors in the header and sill. Panels themselves last for decades if they are stored flat and dry.

What you can do

Count the panels and fasteners before the season and store them by opening. Replace stripped wing nuts with stainless ones rated for the job.

Call us if

A header or sill track has pulled loose, studs are bent or missing, panels are cracked, or you have panels but no track. Read how to install storm panels properly before you improvise.

Hurricane screens

Parts of a hurricane screen

Hurricane screen parts diagramZipper-track hurricane screen, partly lowered. Based on the StormTex side track assembly.Hood (cassette)holds the rolled-up fabricAxle and motor60 mm axle inside the hoodSide railwith inner channelKeder (zipper edge)welded to the fabric edgeBottom hembarweights and seals the bottomScreen fabrichurricane or everyday fabricPlastic tension springkeeps the edge tight in the railSnap-in screw cover
What wears out

The keder edge, the tension spring and the bottom hembar. Fabric can tear at the edge if it is run out of its track, and motors wear like any roll down motor.

What you can do

Keep the side rails clear and never run the screen with something in its path. Rinse the fabric with fresh water after a storm.

Call us if

The fabric comes out of a rail, will not track straight, is torn, or the motor stops. Our hurricane screens page covers the systems we install.

When a DIY parts fix is the wrong choice

Cleaning and lubricating are yours. These are not.

Anything that holds the shutter to the wall
Anchors, tracks and their fasteners were sized by an engineer for your wind zone. Do not remove or change them.
Springs and motors under load
A roll down curtain carries its own weight on the tube. Taking apart a hood with the curtain attached can injure you.
Before a storm, with no time to spare
If a shutter will not deploy and a storm is coming, call us. Broken shutters come first before a storm.

Hurricane shutter parts questions

What are the main parts of a roll down shutter?
The housing at the top, the reel tube inside it, the slats that form the curtain, the side rails the curtain runs in, the base slat at the bottom, and either a motor or a crank to turn the tube. Straps called slat hangers connect the curtain to the tube.
What is a centermate on an accordion shutter?
The centermate is the blade where the two halves of an accordion shutter meet in the middle. It carries the lock and, on many systems, a locking rod that drops into the bottom track.
Why will my accordion shutter not slide?
Usually sand and salt in the bottom track, or worn or broken wheels in the wheel carriage at the top. Clean the bottom track first. If it still drags, the wheels or bushings need replacing.
What is an override motor?
A roll down motor with a manual backup. A crank handle connects through an extension shaft and universal joint, so you can raise or lower the shutter by hand when the power is out.
What holds a Bahama shutter open?
Telescoping side arms, an inner and an outer aluminum pipe, locked to length with a tension ring and thumbscrew. For a storm the arms come off and the shutter is lowered and pinned closed.
How do I find out who made my shutters?
Rated shutters carry a permanent label, often inside the housing, on the track or on the bottom of a panel, with the manufacturer and product approval. Send us a photo of the label and we can usually tell you what you have.

Why homeowners call AHS for service

Family-owned since 2006. We answer emergency calls 24/7.

Licensed in NC and SC
NC General Contractor L.66775 · SC General Contractor CLG.118108.GC
4.7 stars on Google
From 65 Google reviews.
Parts on the Truck
Most repairs are done in one visit.

Need a Part Replaced?

Call to book a service call. Most parts are on the truck, so most repairs take one visit.

(910) 256-1288
Available 24/7 · (843) 868-1390 in SC
Request Service
Matthew Burns
Scroll to Top